Use this fuel economy calculator to calculate MPG from distance and actual fuel used over the same interval. See , , and , or convert an existing fuel economy value.
Measure distance and fuel over the same interval
Fuel economy tells you how far you travel per unit of fuel. Consumption reverses that relationship and tells you how much fuel a distance uses. Both need matching distance and fuel measurements. FuelEconomy.gov and EMSD use successive full fills to establish that interval. Both sources are listed in References. The same measured distance divided by fuel volume applies to gasoline/petrol, diesel and other liquid fuels, with no fuel-type conversion factor.
Record the odometer when the tank is full, or reset the trip meter. Exclude the fuel bought for this initial fill: it establishes the starting fuel level.
Record every refill after the baseline, including partial refills and the final full fill. Add those volumes using the same unit. The final full fill restores the starting level, so the added fuel represents fuel used over the interval.
Use the distance between the starting and ending full fills. In More options, choose Odometer readings to enter both readings in the same distance unit. Do not substitute tank capacity, money spent or fuel-gauge movement for measured fuel use.
For several complete, non-overlapping full-to-full intervals, add their distances and fuel volumes separately, then calculate from those totals. Do not take an unweighted average of individual MPG readings: the intervals may use different fuel quantities. For consumption, use total liters divided by total kilometers on the stated distance basis.
Calculate MPG, km/L and L/100 km
= miles traveled ÷ US liquid gallons used. = miles traveled ÷ Imperial gallons used. = kilometers traveled ÷ liters used.
= 100 × liters used ÷ kilometers traveled. This reciprocal measure follows EMSD’s consumption equation. When you enter odometer readings, distance is the ending reading minus the starting reading. The calculator subtracts before converting units.
The exact normalization factors are 1 = 1.609344 and 1 = 3.785411784 from NIST Handbook 44. One Imperial gallon = 4.54609 from NIST Appendix B.9. Intermediate values are not rounded.
Calculate and Convert both display up to 12 significant digits, with half-up rounding. The ≈ mark identifies a rounded value, and scientific notation keeps small nonzero results visible. Copy uses the same displayed values and readable units. Extra digits do not improve the precision of your measurements.
Check a measured trip
Choose the US trip example in Calculate. Its complete state uses distance entry, 300 and 10 over the same interval. The figures illustrate the arithmetic; they are not a typical vehicle rating.
Divide distance by fuel: 300 ÷ 10 = 30 .
The engine converts the distance to 482.8032 and the fuel to 37.85411784 . Dividing those metric quantities gives ≈ 12.7543112229 .
The same journey is ≈ 36.0284977651 , or ≈ 7.84048611111 . The unit labels change the number, not the measured journey.
Read US MPG, Imperial MPG and metric consumption
An Imperial gallon holds more fuel than a US liquid gallon. The same measured journey therefore has a higher number. An unlabeled MPG figure is ambiguous: check the original source before selecting US or Imperial. NIST’s volume table distinguishes the gallon conventions.
Higher MPG or means more distance per unit of fuel. Lower means less fuel for the same distance. These move in opposite directions because consumption is reciprocal to distance per fuel volume. Convert units before comparing figures, then check that their measurement conditions are comparable. Changing units cannot reconcile different driving conditions or test methods.
Convert an existing fuel economy value
Choose Convert when you already know a fuel economy or consumption rate. Enter its value and select , , or . The calculator shows all four equivalents and the conversion steps for that input.
Use the gallon convention supplied with the original figure, including when comparing Canadian, US or UK listings. A location alone does not establish the unit behind a copied MPG number. The table below uses explicitly labeled inputs.
These selected values show equivalent rates, not vehicle ratings or efficiency targets.
| 10 | ≈ 12.009499255 | ≈ 4.2514370743 | ≈ 23.5214583333 |
| 20 | ≈ 24.0189985101 | ≈ 8.50287414861 | ≈ 11.7607291667 |
| 30 | ≈ 36.0284977651 | ≈ 12.7543112229 | ≈ 7.84048611111 |
| 40 | ≈ 48.0379970202 | ≈ 17.0057482972 | ≈ 5.88036458333 |
| 50 | ≈ 60.0474962752 | ≈ 21.2571853715 | ≈ 4.70429166667 |
| 60 | ≈ 72.0569955303 | ≈ 25.5086224458 | ≈ 3.92024305556 |
Values use the calculator’s display precision. The ≈ mark means rounded. Unit definitions come from NIST Handbook 44 and NIST Appendix B.9, listed in References.
What a measured result can tell you
A full-to-full result describes the recorded interval. If the starting and ending fuel levels differ, the refilled volume does not exactly represent fuel used. Missing refill records also break the measurement. Driving conditions and measurement methods can differ between intervals, a dashboard display and an advertised rating; EMSD’s guidance notes variation with vehicle condition and driving habits.
The calculator requires positive distance and fuel use. Zero distance makes consumption per distance undefined; zero fuel makes distance per fuel undefined. Those inputs produce an error rather than an invented finite answer. An ending odometer reading must exceed the starting reading; rollover and replacement odometers need a separately established distance.
Enter plain decimals without commas, fraction notation or exponents. Each numeric field accepts at most 24 characters, 18 significant digits and 9 decimal places, with a maximum value of 1,000,000,000 measured using its selected unit. These are calculator input limits, not vehicle limits.
This result does not diagnose a vehicle, grade its efficiency, promise savings or predict remaining range. There is no vehicle database, route planner, fuel-cost estimate, fuel-needed mode or comparison of future purchases. It also does not measure electricity use or energy-equivalent MPGe.
If you only need to change a known fuel volume between liters and labeled gallons, the Volume Converter handles that quantity without a distance. To find average speed from distance and elapsed time, use the Speed Calculator.
Frequently asked questions
What does 50 MPG consume in liters?
At 50 , consumption is ≈ 4.70429166667 . At 50 , it is ≈ 5.64961872664 . Check which gallon convention the quoted MPG uses. These are rates per 100 , not the total liters used on a journey. Total fuel also depends on distance. The conversion uses the exact unit definitions in NIST Handbook 44 and NIST Appendix B.9, listed in References.